CAN I INSTALL A BATH TUB MYSELF?

Can I Install A Bath Tub Myself?

Can I Install A Bath Tub Myself?

Blog Article

Call Us Today

This post listed below on the subject of How to Install a Bathtub Yourself is extremely remarkable. Don't miss out on it.


Installing A Bathtub
Setting up a bath tub isn't precisely brain surgery, but it does need solid plumbing, carpentry, as well as often, tiling skills. Changing an old bathtub with a brand-new one is additionally a reasonably hard job. If the old bathtub is easily easily accessible, the job can relocate immediately; if you need to open a wall to eliminate the old tub and place the brand-new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will certainly require an assistant to vacate the old tub and set in the brand-new one. Make certain you have qualified on your own for the work as well as are comfortable attempting it. Rather than employing a specialist to take over a halfway-completed project, it is better to take into consideration utilizing one prior to you start. Possibilities are you might require a professional plumber to make tube links.
This short article will certainly aid you mount a new tub in your washroom if you have actually already bought a brand-new tub and don't require to alter the arrangement of your previous water supply pipelines.
Your tools and also material checklist need to make up the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Planning for the Setup


    Firstly, the sustaining framework supplied with the bath ought to be fitted (if called for) according to the maker's instructions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps device to prevent stress on the tub.
    Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you make use of all of the supplied washers.
    Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its last position.

    Removing Old Touches


    If you need to replace old faucets with new ones as a part of your setup, after that the first thing you must do is detach the water supply. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The process of removing the existing faucets can be quite troublesome due to the restricted access that is typically the case.
    Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a cloth all set for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been gotten rid of, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. Once the taps have been removed, the holes in the bath/basin will certainly have to be cleaned up of any old sealing compound.
    Before going on to fit the new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.

    Installing the Bath tub


    Using the two wood boards under its feet, put the bathtub in the needed placement. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four small points.
    The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and adjusting the feet on the bath tub up until the spirit level reads degree.
    To set up faucets, fit all-time low of the outermost flexible faucet connector to the proper supply pipeline by making a compression sign up with; then do the very same for the other faucet.
    Activate the supply of water and also inspect all joints and also new pipework for leakages and tighten them if necessary. Fill the bathtub as well as likewise examine the overflow electrical outlet and also the regular electrical outlet for leakages.
    Finally, deal with the bath paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been made use of at least when as this will certainly resolve it into its final placement.

    Suitable New Touches


    If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipelines.
    If you require to fit a monobloc, then you will require reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in place in between the tap and the sink. Safeguard the tap in place with the supplier given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind needs to be linked to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.

    Tiling Around the Tub


    In the area where the bathroom satisfies the tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, resulting in issues with moisture as well as possible leakages to the ceiling below.
    You can select from a selection of coloured sealers to blend in your components and also installations. They are sold in tubes as well as cartridges, and also are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched paper or soft rope. Remember to constantly fill the bath tub with water prior to securing, to permit the motion experienced when the tub is in use. The sealer can crack rather very early if you do not consider this activity prior to securing.
    Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant sticky and cement.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    Tools You Need to Install a New Bathtub

    Do you enjoy reading about How to Install a Bathtub? Post a remark below. We will be interested to see your responses about this write up. We hope that you visit us again later on. Those who liked our page kindly do not forget to share it. Thanks a lot for your time. Come back soon.




    Request Service


    Report this page